How to best hang this piece of art?
February 26, 2013 2:06 PM
I have a large (but not terribly heavy) wooden shield that I'd like to hang. Yesterday I used two eye screws, wrapped wire around the handle, and tried to suspend it.
Pic of the back of the shield here: http://tinypic.com/r/34ffwbk/7
Unfortunately there's no stud, it needs to hang in a very specific location, and the eye screws were too short. To be honest it was a little sub-par as a solution anyway. All the grip clamps (like you'd use to hang a broom) at the hardware store are either too big or too small.
How would you mount this? With the handle on the back, the piece extends about four inches from the wall. I'm willing to trudge back out into the frozen wasteland and hit up the hardware store again, but not if I don't have to. Thank you!
I should have said that it's kind of an artifact, so nails or screws in it aren't an option. It's all carved from one piece of wood, but I could maybe make a loop with a piece of wire coat hanger and then use that to suspend it....
posted by 2soxy4mypuppet at 2:16 PM on February 26, 2013
posted by 2soxy4mypuppet at 2:16 PM on February 26, 2013
Maybe take it with you to the hardware store and ask them for clamping suggestions? I go to hardware stores with crazy art project problems all the time and they love to help me out.
posted by leslies at 2:19 PM on February 26, 2013
posted by leslies at 2:19 PM on February 26, 2013
It's not heavy, but I really hate to take it on the bus.
posted by 2soxy4mypuppet at 2:29 PM on February 26, 2013
posted by 2soxy4mypuppet at 2:29 PM on February 26, 2013
How "not heavy" are we talking? I've just started using these 3M removable hangers Not the hooks, they've got a little stud thing and you hang the wire on them like you would a nail.
I've hung a bunch of large-ish frames very successfully. You could try using 2 if you're concerned about the weight (Not clear on the orientation you're hanging your shield, might not be enough room for two.
They're supposed to hold 8lb with one though, which is about a gallon of milk, so you may be surprised, and they're cheap enough and undemanging enough to try without feeling like it absolutely must work.
posted by dadici at 2:35 PM on February 26, 2013
I've hung a bunch of large-ish frames very successfully. You could try using 2 if you're concerned about the weight (Not clear on the orientation you're hanging your shield, might not be enough room for two.
They're supposed to hold 8lb with one though, which is about a gallon of milk, so you may be surprised, and they're cheap enough and undemanging enough to try without feeling like it absolutely must work.
posted by dadici at 2:35 PM on February 26, 2013
I would actually support it from the bottom and the sides, rather than from the back.
I'm picturing something like one or two L-shaped braces at the bottom for actual support, depending on the shape of the bottom of the shield, then one one each side just below the widest part of the shield for balance and stability. Easily built of wood, shelving braces, or a combination of the two.
posted by batmonkey at 3:11 PM on February 26, 2013
I'm picturing something like one or two L-shaped braces at the bottom for actual support, depending on the shape of the bottom of the shield, then one one each side just below the widest part of the shield for balance and stability. Easily built of wood, shelving braces, or a combination of the two.
posted by batmonkey at 3:11 PM on February 26, 2013
What about a curtain rod -- you use the brackets but get a dowel cut to size. That way it could be lifted off as necessary. The dowel could fit through the handle. However, the hardware would need to reach out far enough to easily go through the handle and that may be too fussy.
Otherwise, yes on molly bolt or drywall anchors in general, but it seems to me that the thing needs some stability. Maybe two of these mounted side by side with, again, a dowel cut to size to push through the handle.
Or! I'd get some hefty looking sisal or hemp rope and do a figure 8 loop through the handle with a knot leading off the top edge and then hook it on something sturdy, like this only maybe something a little sexier, like a cleat! Especially if you can find one that jibes with the spirit of the piece -- brushed metal or black or rustic somehow.
Take your photo in on your phone and show the hardware store. I'd look for the hanger to have at least two screwholes and then make sure you use drywall anchors.
posted by amanda at 3:31 PM on February 26, 2013
Otherwise, yes on molly bolt or drywall anchors in general, but it seems to me that the thing needs some stability. Maybe two of these mounted side by side with, again, a dowel cut to size to push through the handle.
Or! I'd get some hefty looking sisal or hemp rope and do a figure 8 loop through the handle with a knot leading off the top edge and then hook it on something sturdy, like this only maybe something a little sexier, like a cleat! Especially if you can find one that jibes with the spirit of the piece -- brushed metal or black or rustic somehow.
Take your photo in on your phone and show the hardware store. I'd look for the hanger to have at least two screwholes and then make sure you use drywall anchors.
posted by amanda at 3:31 PM on February 26, 2013
You might be able to use a wall bracket for a guitar, especially if you have some extra cushioning
posted by Heart_on_Sleeve at 3:35 PM on February 26, 2013
posted by Heart_on_Sleeve at 3:35 PM on February 26, 2013
« Older What's a good normal lens for a Canon Rebel T4i? | Help with Tumblr - Can I install this plugin? Newer »
This thread is closed to new comments.
Are you wanting the piece to hang perfectly straight? Because you could get fancy and mount a piece of wood on the wall as a cleat to hang from - that's going to be a big more of a production though.
posted by leslies at 2:12 PM on February 26, 2013