I have a bridged router acting as a modem, and a non-wireless vpn router. I need two add one or two wireless routers...how? [more inside]
posted by Unhyper on Sep 29, 2012 - 2 answers

Using two Cisco RVS4000 routers to create a VPN between two offices. A tunnel is supposedly set up successfully, because the router says it's "up" and I can access the admin interfaces of both routers from both locations by using their internal IPs (192.168.1.1 and 192.168.2.1). Trouble is, I can't reach any of the workstations or peripherals behind the routers. [more inside]
posted by Unhyper on Apr 2, 2012 - 17 answers

Help me configure my CISCO 877 router... [more inside]
posted by Bacillus on Jul 13, 2011 - 10 answers

Please help me configuring my Cisco 877 small business router for the Internet... [more inside]
posted by Bacillus on Jul 5, 2011 - 5 answers

My wireless router is driving me insane. After trying everything I know (changing wireless channels, upgrading the firmware) should I just give up, throw money at the problem and upgrade to what seems to be the top of the line? [more inside]
posted by falameufilho on May 26, 2011 - 28 answers

What are the wireless ranges of the 802.11g radios in the following: WRT54G WRT610N I specifically would like to know the range of each and does the WRT610N 802.11G radio have a greater range than the WRT54G 802.11G radio. Not surprisingly, Linksys couldn't even help me.
posted by paulyballs on Feb 16, 2010 - 3 answers

How do I configure my VOIP gateway (CISCO Linksys SPA-3102) for a multi-number phone line? [more inside]
posted by Bacillus on Jan 24, 2010 - 5 answers

I just put in a new router (cisco wireless n broadband router wrt160N) and it is totally fast when the ethernet cable is plugged into my computer. When I try to use it wirelessly, it works but is VERY slow. any ideas? thanks!!!!!
posted by cg2 on Dec 9, 2009 - 10 answers

How do I learn how to use a Cisco Router? [more inside]
posted by talkingmuffin on Nov 18, 2009 - 12 answers

One Cisco router, two ISPs - gateway redundancy? [more inside]
posted by doomtop on Jun 18, 2009 - 10 answers

Hi, I have two Cisco 2610 routers, each with WIC-1DSU-T1 cards. We have a Point-to-Point between two locations and I am using these to route the traffic between. The lines belong to Verizon and the AdTran cards are locked in a Verizon box. I can look in and see the status lights through the top. Each location has a RJ48X loopback jack. When I plug in the Cisco at Location 1 it seems to hook up fine, and the carrier detect light pops up. (Which is strange to me because our PTP is unmonitored and I thought the CD would only come on when equipment is plugged into both ends.) Then when I go and plug in the Cisco at Location 2, I get no lights, no nothing. I check the lights in the Verizon box and an alarm is triggered with a red LED. I disconnect the Cisco and it clears the alarm. How can I figure out what the problem is? I had the company that provides the PTP come and check the circuit originally and they said they found problems but that the problems had gone away now. Is it possible that the WIC-1DSU-T1 card in this router is faulty? Any help is appreciated! Thanks.
posted by doomtop on Feb 14, 2007 - 6 answers

I am on a VLAN and cannot browse the domain. I can connect to servers e.g. //server1/ and see the dives etc. If I am on the same VLAN as the server - I can browse and see everything. Is there perhaps a broadcast or something that the Cisco router is not allowing through? Tried ip forward-protocol udp netbios-ns Any ideas? Thanks
posted by bright77blue on Jun 3, 2006 - 6 answers

Who makes a reliable home firewall/router? [more inside]
posted by b1tr0t on Oct 25, 2005 - 17 answers