Comments on: How to fix a burred laptop screw

Question: How to fix a burred laptop screw

zaebiz — Fri, 15 Jun 2007 19:51:27 -0800

I am trying to replace a laptop keyboard but the final screw has burred and neither the regular or precision screwdriver works. If someone suggests that I go to repairman and 50 bucks to fix this, I am likely to do serious damage to this laptop (namely by throwing it against a wall). Any ideas?

The screw is a tiny, flat-headed, star-head screw. I don't care about doing damage to the outside of the case as long as I dont damage the internals. I just want this sucker out. This laptop doesn't deserve to live, let alone look pretty. (Thinkpad T42)

By: pupdog

pupdog — Fri, 15 Jun 2007 19:55:25 -0800

Try a pair of needlenose pliers - you should be able to grip the edges of the screw enough to twist it, unless it's countersunk. Another option is a tiny drill bit, and just cut it out.

By: kc8nod

kc8nod — Fri, 15 Jun 2007 20:25:46 -0800

Buy a screw extractor here, here or possibly at Sears. The screw itself will be ruined in the process.

If you can't wait that long, perhaps you could bond the screw to the tool with a bit of epoxy?

By: davey_darling

davey_darling — Fri, 15 Jun 2007 20:26:12 -0800

Try a slightly larger screwdriver (star headed or "phillips" as they're known) and push very hard while turning. I've found that you can often get enough grip to get the screw started and out.

By: caddis

caddis — Fri, 15 Jun 2007 20:27:01 -0800

You need to go to home depot and get a screw extractor. It is a reverse thread screw. You drill a little pilot hole into the stuck screw and then screw the extractor in counter clockwise. It will grip the screw and dislodge it. The only trick will be finding one small enough for a laptop case screw.

By: jet_silver

jet_silver — Fri, 15 Jun 2007 20:36:50 -0800

If you have a Dremel tool with a thin cut-off wheel, you cut a thin slot in the head of the screw, and use a flat-bladed driver on that one.

By: itheearl

itheearl — Fri, 15 Jun 2007 20:57:29 -0800

I wanted to open a star-screwed hard drive once, but didnt have a small enough star driver.

Get a very small slotted screwdriver and see if you can get it to catch in the star.
If it does, use one hand to push down very firmly on the base of the screwdriver, and use the outer to turn the driver until the screw breaks loose.

Pushing down hard and not letting the driver get loose and strip out the screw is key. You might be able to get it out with your star driver even if it is stripped just by holding it at an angle so that it grips while you push hard on the base of it with one hand and turn it with the other.

By: one_bean

one_bean — Fri, 15 Jun 2007 21:05:14 -0800

I stripped some screws a few years ago trying to get a failed hard drive out of my laptop. I brought it to the hardware store down the block and asked them what tool I'd need to get it out. They brought the tools out and did it for me -- no charge.

By: autojack

autojack — Fri, 15 Jun 2007 23:23:46 -0800

The suggestions of either epoxy-ing the tool to the screw, or using a dremel to cut a notch in it for easier removal, would be my two preferred solutions.

By: zaebiz

zaebiz — Fri, 15 Jun 2007 23:46:51 -0800

Going to try the hardware store charity approach first, and then the epoxy approach. I don't have many tools available and the screw is really wedged right in there and very burred.

If all else fails Im going to punch holes in the sucker with precision screwdriver and just yank the little $%head out of its casing.

Thanks for the ideas.

By: Chuckles

Chuckles — Sat, 16 Jun 2007 15:04:50 -0800

If you are going to go that far, better to drill out the screw head. The screw location will be unusable, because the old screw shaft will still be in the whole, but it won't look too bad.

By: zaebiz

zaebiz — Sat, 23 Jun 2007 20:33:06 -0800

Update : the hardware guy fixed it for free.