Comments on: Where can I find large adhesive panels?

Question: Where can I find large adhesive panels?

OverlappingElvis — Sat, 24 Jun 2006 12:15:10 -0800

I'm working on a craft-type project that, when finished, will involve adhering large nylon panels to plastic or metal surfaces. I've done a few sample versions of this by covering cardstock in cloth tape, putting my image on the tape, and then using more of the matching cloth tape to adhere the panel to the surface. There has to be a better way to do this with the nylon, though - is there such a thing as large double-sided adhesive sheets that can turn a reasonably light piece of cloth/sythetic/paper into what's essentially a giant sticker?

By: radioamy

radioamy — Sat, 24 Jun 2006 12:23:52 -0800

spray adhesive might be what you are looking for

By: StickyCarpet

StickyCarpet — Sat, 24 Jun 2006 12:31:41 -0800

Double sided adhesive materials are available in up to 48" rolls. 3M makes some as do others.

By: DenOfSizer

DenOfSizer — Sat, 24 Jun 2006 14:59:48 -0800

I was going to point out spray adhesive, too (always spray it lightly on your surfaces, and for the love of noodles, please, PLEASE, spray that shit somewhere well-ventilated, and mind your valuables as you spray) but perhaps you could also try some of those velcro tabs.

By: Chuckles

Chuckles — Sat, 24 Jun 2006 15:38:15 -0800

I think a giant sticker could get hard to handle, even small stickers are a pain, so an adhesive (spray, or whatever else) might be better.

I guess you don't want to hold it up while it dries?

Also, you probably don't need all those square feet of bonding surface. Just a few strips of double sided tape across the back would be able to hold up a fair bit of weight. Actually, double sided foam tape, I think. It seems to do a better job of bonding to irregular surfaces.

Anyway, McMaster-Carr has everything. It is hard to deep link on their site, but try searching for Rubber and Foam, and then selecting either Sheets, Bars and Strips or Film. On the new page you will be able to select Adhesive, and so on..

By: Chuckles

Chuckles — Sat, 24 Jun 2006 15:42:01 -0800

Also..
Aerosol Spray seems convenient when you look at it in the store, but spray is actually very messy. That goes for paint, oil, grease, adhesive, whatever. Not that it is always bad or anything, but I think people tend to pick spray first nowadays, and that is probably wrong.

By: Chuckles

Chuckles — Sat, 24 Jun 2006 15:43:05 -0800

And I forgot the link.. McMaster-Carr.

By: Mitheral

Mitheral — Sat, 24 Jun 2006 15:48:39 -0800

If a spray adhesive like 3M Super77 is too messy you could roll on a latex contact adhesive. You'll need to coat both surfaces and wait for it to dry but it is quite a bit more controllable than the spray.

By: tomble

tomble — Sat, 24 Jun 2006 18:58:56 -0800

A contact adhesive is a good way to do it. Try a carpet tile adhesive if you want a low odour, water based adhesive. I use this a lot at work and it's very strong. This process is easier if you're using an adhesive which sets after you've laid down the item - if it's creased or crooked, you can lift it and re-apply it.

If you're using adhesive on a roll, like a very wide double sided tape, you'll need to be careful when applying it. Once you've covered the back of the first surface, peel an inch or two of the backing paper away at one edge, line up the item to be stuck down and press down the edge onto the exposed adhesive.

You may want to get someone else to reach under the item being stuck down and slowly peel the backing paper from the adhesive as you carefully press down the item to the now exposed adhesive with a soft cloth.

Take care with wrinkling, this process can require quite a bit of practice.

If you're looking to buy an adhesive film, the 3M material is very good, but quite expensive (it's often used in high end applications). You should be able to get a generic material that will suit your purporses from any company which sells laminating film.